Elecro Swimming Pool Heat Exchangers
Elecro Heat Exchanger
Construction
The Elecro heat exchanger is manufactured from top quality components and material at the Elecro works in Hertfordshire, England.
Construction consists of a densely populated multi-tubular pure Titanium tube bundle which is secured by the purpose designed polyamide / rubber tube sheet. The heat exchanger shell is constructed from BS 316 Stainless Steel this is capped at each end with primary and secondary moulded fittings manufactured from specially formulated polymer alloy material.
The heat exchanger is supported on two swivel feet; to facilitate either wall or floor mounting.
The heat exchanger is supplied complete with:
- 2 x 1" male/male Brass primary connections
- 1 x 1" Brass Non-return valve
- 1 x Titanium thermostat pocket
- 1 x Blanking cap & coin gasket (for non-thermostat side)
The Elecro heat exchanger has been designed to allow the installation engineer
to select which way to plumb the primary and secondary water to achieve maximum
thermal gain, this is achieved by routing the primary (HOT) flow in an opposing
direction to the secondary (POOL) water.
Operation
The Elecro heat exchanger is installed in the swimming pool filtration circuit from which water passes through the tube side of the heat exchanger. Water from the primary heating circuit flows counter current through the shell side of the exchanger, heating the swimming pool water.
Elecro heat exchangers are ideal for use with gas or oil fired boiler circuits, solar panels, heat pumps or chillers.
- Robust, durable construction
- Titanium or Stainless Steel tube bundle
- Straight through water path
- 316 Stainless Steel shell with special polyamide fittings
- May be floor or vertically wall mounted
| Elecro swimming pool heat exchanger data sheet |  |
Tube bundle |
Standard Power Output |
Water connections |
1 1/2" or 50-mm rigid
pipe |
Heating circuit connections |
1" BSP |
Maximum operating pressure |
4 barg |
Mounting |
Floor or wall mountable |
Please select the heat exchanger you want and then an optional equipment
kit if desired
Product Code |
Standard Power Output |
Buy Now |
EHE25T |
25-kW / 85,300 BTU |
|
EHE40T |
40-kW / 136,480 BTU |
|
EHE70T |
70-kW / 238,840 BTU |
|
EHE100T |
100-kW / 341,200 BTU |
Elecro Analogue Swimming
Pool Heat Exchanger Option Kit |
Elecro Digital Swimming
Pool Heat Exchanger Kit |
Construction The Elecro analogue swimming pool heat exchanger kit is manufactured from top quality components and material at the Elecro works in Hertfordshire, England. Construction consists of a densely populated multi-tubular pure Titanium tube bundle which is secured by the purpose designed polyamide / rubber tube sheet. The heat exchanger shell is constructed from BS 316 Stainless Steel this is capped at each end with primary and secondary moulded fittings manufactured from specially formulated polymer alloy material The heat exchanger is supported on two swivel feet; to facilitate either wall or floor mounting. The Analogue equipped heat exchanger is supplied complete with:
The Elecro analogue equipped heat exchanger has been designed to allow the installation engineer to select which way to plumb the primary and secondary water to achieve maximum thermal gain, this is achieved by routing the primary (HOT) flow in an opposing direction to the secondary (POOL) water. Operation The required pool temperature can be easily selected by rotating the thermostat dial to the required temperature. When the incoming pool water reaches the desired temperature the thermostat switches the booster pump and heating appliance off. The booster pump and heating appliance is switched back on if the pool water temperature falls below the required temperature. A volt-free contact is supplied; this can be wired to the heating appliance to switch it on and off. Elecro
heat exchangers are ideal for use with gas or oil fired boiler
circuits, solar panels, heat pumps or chillers. |
Construction The Elecro digital swimming pool heat exchanger kit is manufactured from top quality components and material at the Elecro works in Hertfordshire, England. Construction consists of a densely populated multi-tubular pure Titanium tube bundle which is secured by the purpose designed polyamide / rubber tube sheet. The heat exchanger shell is constructed from BS 316 Stainless Steel this is capped at each end with primary and secondary moulded fittings manufactured from specially formulated polymer alloy material The Elecro swimming pool heat exchanger digital kit is supported on two swivel feet; to facilitate either wall or floor mounting. The fully equipped heat exchanger is supplied complete with:
The Elecro fully equipped heat exchanger has been designed to allow the installation engineer to select which way to plumb the primary and secondary water to achieve maximum thermal gain, this is achieved by routing the primary (HOT) flow in an opposing direction to the secondary (POOL) water. Operation The required pool temperature can be easily input into the digital thermostat using the keypad on the front panel which is then clearly displayed, the actual water temperature is also displayed. The Elecro digital equipped heat exchanger features priority heating which enables the thermostat to override the pool circulation pump timer to switch on the pool recirculation pump and the heating appliance in order to maintain the required pool temperature at all times. A volt free contact is supplied. This can be wired to the heating appliance to switch it on and off. Elecro heat exchangers are ideal for use with gas or oil fired boiler circuits, solar panels, heat pumps or chillers. |
